cmy210 datasheet ultra-linear mixer with integrated lo buffer a pplications ? up- or down- converters ? mobile phones receivers ? wlan receivers ? mobile phone or wlan basestations features ? very high input ip3 of 24 dbm typical ? very low lo power demand of 0 dbm typical; wide input range ? wide lo frequency range: <500 mhz to >2.5 ghz ? single-ended ports ? rf- and if-port impedance 50 ohms ? operating voltage range: <3 to 6 v ? very low current consumption: 6 ma typical ? all gold metalization package outline, m w -6 description the cmy210 is an all port, single-ended, general purpose up- and down-converter. it combines small conversion losses and excellent intermodulation characteristics with a low demand of lo- and dc-power. the internal level controlled lo-buffer enables good performance over a wide range of lo level inputs. the mixer configuration allows rf or if feed to either pin 1 or 6 and thus requires a frequency separation circuit on the pc board. 1 2 3 4 5 6 gnd gnd rf or if lo in if or rf v dd f o r additional information and latest s pecifications, see our w ebsite: w w w .triquint.com 2 revision e, september 12, 2006
cmy 210 datasheet ________________________________________________________________________________________________________ for additional information and latest s pecifications, see our website: www.triquint.com 3 revision e, september 12, 2006 maximum ratings parameter port symbol value unit min max supply voltage 4 v dd 0 6 v dc-voltage at lo input 3 v 3 -3 0,5 v dc-voltage at rf-if ports 2) 1, 6 v 1,6 - 0,5 + 0,5 v power into rf-if ports 1, 6 p in,rf 17 dbm power into lo input 3 p in,lo 10 dbm channel temperature t ch 150 c storage temperature t stg -55 150 c thermal resistance channel to soldering point (gnd) r thchs 100 k/w 1) for detailed dimensions see page 7. 2) for dc test purposes only, no dc vo ltages at pins 1, 6 in application
cmy 210 datasheet ________________________________________________________________________________________________________ f o r additional information and latest s pecifications, see our w ebsite: w w w .triquint.com 4 revision e, september 12, 2006 electrical characteristics test conditions: t a = 25c; v dd = 3v, see test circuit; f rf = 808mhz; f lo = 965mhz; p lo = 0dbm; f if = 157mhz, unless otherwise specified: parameter, test conditions sy mbol min ty p max unit operating current i op - 6 . 0 8 . 0 m a conversion loss l c - 5 . 7 7 . 0 d b ssb noise figure f ssb - 6 . 0 - d b 2 tone 3rd order imd p rf1 = p rf2 = -3dbm f rf1 = 806mhz; f rf2 = 810mhz; f lo =965mhz d im3 - 5 4 - d b c 3rd order input intercept point ip3 in 2 0 2 4 - d b m p -1db input power p -1db - 1 4 - d b m lo leakage at rf/if-port (1,6) p lo 1,6 - - 8 - d b m applications information test circuit / application example i n / out rf 50 o h m out/ i n 50 o h m if l1 l2 c1 c2 vd d c4 l4 lo i n l3 c3 c m y 210 6 1 2,5 4 3 notes for external elements: l1, c1: filter for upper frequency; c2, l2: filter for lower frequency; each filter is a throughpath for the desired frequency (rf or if) and isolates the other frequency (if or rf) and its harmonics. these two filters must be connected to pin 1 and pin 6 directly. parasitic capacitances at the ports 1 and 6 must be as small as possible. l4 and c4 are optimized by indicating lowest i op at used lo- frequency; same procedure for l3. the ports 1, 3 and 6 must be dc open. lumped element values for 800mhz test and application circuit: f lo f rf f if l 1 c 1 l 2 c 2 l 3 c 3 l 4 c 4 m h z m h z m h z n h p f n h p f n h p f n h p f 9 6 5 8 0 8 1 5 7 8 . 2 3 . 9 8 . 2 3 . 3 6 . 8 4 7 1 5 3 3
cmy 210 datasheet ________________________________________________________________________________________________________ f o r additional information and latest s pecifications, see our w ebsite: w w w .triquint.com 5 revision e, september 12, 2006 applications information (cont) pcb-layout for 800mhz test and application circuit: 8. 2nh 8. 2nh 6. 8 n h 33 pf 33 pf 15nh c m y 210 3. 3pf 3. 9 p f a c t ual size typical lumped element values for different rf-frequencies: f rf l 1 c 1 l 2 c 2 m h z n h p f n h p f 4 0 0 1 2 1 5 1 2 1 2 4 5 0 1 2 1 2 1 2 1 0 9 0 0 8 . 2 3 . 9 8 . 2 3 . 3 1 5 0 0 3 . 3 2 . 7 3 . 3 2 . 2 1 8 0 0 3 . 3 2 . 2 3 . 3 1 . 8 2 0 0 0 3 . 3 1 . 8 3 . 3 1 . 2 2 4 0 0 1 . 8 2 . 7 1 . 8 1 . 5 typical lumped element values for different lo-frequencies: f lo l 3 c 3 l 4 c 4 m h z n h p f n h p f 5 0 0 1 5 8 2 4 7 8 2 7 5 0 6 . 8 3 3 2 2 3 3 8 0 0 6 . 8 3 3 1 8 3 3 9 5 0 6 . 8 2 7 1 5 2 7 1 1 0 0 6 . 8 2 7 1 2 2 7 1 4 0 0 6 . 8 2 2 6 . 8 2 2 1 6 0 0 6 . 8 1 8 4 . 7 1 8 1 8 0 0 6 . 8 1 5 3 . 3 1 5 2 0 0 0 6 . 8 1 2 2 . 2 1 2 2 1 0 0 6 . 8 1 2 1 . 8 1 2 2 3 0 0 4 . 7 1 2 1 . 2 1 2
cmy 210 datasheet ________________________________________________________________________________________________________ for additional information and latest s pecifications, see our website: www.triquint.com 6 revision e, september 12, 2006 general description and notes the cmy 210 is an all port single ended general purpose up- and down-converter. it combines small conversion losses and excellent intermodulation characteristics with a low demand of lo- and dc-power. the internal level controlled lo-buffer enables a good performance over a wide lo level range. the internal mixers principle with one port rf and if requires a frequency separation at pin 1 and 6 respectively. note 1: best performance with lowest conversion loss is achieved when each circuit or device for the frequency separation meets the following requirements: input filter: throughpass for the signal to be mixed; refl ection of the mixed signal and the harmonics of both. output filter: throughpass for the mixed signal and reflec tion of the signal to be mixed and the harmonics of both. the impedance for the reflecting frequency range of each filter toward the ports 1 and 6 should be as high as possible. in the simplest case a series- and a parallel- res onator circuit will meet these requirements but also others as appropriate drop in filters or micro stripline elements can be used. the two branches with filters should meet immedi ately at the package leads of the port 1 and 6. parasitic capacitances at these ports must be kept as small as possible. the mixer also can be driven with a source- and load impedance different to 50 ? , but performance will degrade at larger deviations. note 2: the lo-buffer needs an external inductor l4 at port 4; the value of inductance depends on the lo frequency. it is tuned for minimum i op consumption into port 4. at lower lo frequencies it can be r educed by an additional capacitor c5. note 3: the lo input impedance at port 3 can be matched with a series inductor. it also can be tuned for a minimum current i op into port 4. c3 is a dc blocking capacitor. since the input impedance of port 3 can be slightly negative, the source reflection coefficient should be kept below 0.8 ( z 0 = 50 ? ) . the conversion noise figure fssb is corre sponding with the value of conversion loss l c . the lo signal must be clean of noise and spurious at the frequencies f lo f if .
cmy 210 datasheet ________________________________________________________________________________________________________ f o r additional information and latest s pecifications, see our w ebsite: w w w .triquint.com 7 revision e, september 12, 2006 electrical characteristics (cont) -1 0 - 8 - 6 - 4 - 2 0 2 4 6 8 1 0 p lo dbm t h ir d or de r i p 3 ip 3 i n = f ( p lo ) p in = 2 x - 3 d b m ; f if = 40 / 4 5m hz v dd = 3 v ; f lo = p a r a m e t e r ; ip 3 i n dbm 10 15 20 25 30 40 2. 5g h z 0, 5 1, 5 2, 0 2. 5g h z 2. 0 1. 5 1. 0 0. 5 -1 0 - 8 - 6 - 4 - 2 0 2 4 6 8 1 0 p lo db m op erat i n g curren t i op = f ( p lo ) v dd = 3v f lo = pa r a m e te r i op ma 0 2 4 6 8 10 12 14 16 18 20 2. 5g h z 2. 0 -1 0 - 8 - 6 - 4 - 2 0 2 4 6 8 1 0 p lo dbm 0 1 2 3 4 5 6 7 8 9 10 l c db 1. 5 co nversi o n l o ss l c = f ( p lo ) v dd = 3 v ; f if = 12 0m h z f lo = pa r a m e te r 0 1 234 56 78 9 1 0 v dd v l c db 0 1 2 3 4 5 6 7 8 9 10 c onv e r s i on los s l c = f ( v dd ) p lo = 0d b m f lo = 1 500m h z ; f if = 120m h z
cmy 210 datasheet ________________________________________________________________________________________________________ f o r additional information and latest s pecifications, see our w ebsite: w w w .triquint.com 8 revision e, september 12, 2006 electrical characteristics (cont) 0 0 . 5 1. 0 1 . 5 2. 0 2 . 5 gh z f lo lo- l eak age at p o rt 1, 6 p lo 1, 6 = f ( f lo ) p lo = 0d b m v dd = 3v p lo 1, 6 dbm 0 -2 -4 -6 -8 -1 0 -1 2 -1 4 -1 6 -1 8 -2 0 0 1 234 567 8 9 1 0 v dd v i op ma 0 2 4 6 8 10 12 14 16 18 20 oper at ing c u rre nt i op = f ( v dd ) p lo = 0d b m f lo = 150 0m h z
cmy 210 datasheet ________________________________________________________________________________________________________ f o r additional information and latest s pecifications, see our w ebsite: w w w .triquint.com 9 revision e, september 12, 2006 semiconductor device outline m w -6 d i m . m i n . n o m . m a x . g r a d i e n t r e m a r k a 1 . 1 a 1 0 . 1 a 2 1 . 0 b 0 . 3 b 1 0 . 6 c 0 . 0 8 0 . 1 5 d 2 . 8 3 . 0 e 1 . 2 1 . 4 | e | 0 . 9 5 |e 1 | 1 . 9 h e 2 . 6 l e 0 . 6 a m a x 1 0 1 q 2 . . . 3 0 1. applicable on all case top sides
cmy 210 datasheet ________________________________________________________________________________________________________ f o r additional information and latest s pecifications, see our w ebsite: w w w .triquint.com 10 revision e, september 12, 2006 part m a rking part orientation on reel ordering information ty pe marking ordering code (tape and reel) package 1) cmy210 210 cmy210 mw-6 additional information this part is compliant with rohs directive (restrictions on the use of certain hazardous substances in electrical and electronic equipment). the part is rated moisture sensitivity level 1 at 260c per jedec standard ipc/jedec j-std-020. esd: e lectro s tatic d ischarge sensitive device. observe handling precautions. f o r latest specifications, additional product information, w o rldw ide sales and distribution locations, and information about t r iquint: we b: www. t r i q u i n t . c o m t e l: (503) 615-9000 email: in fo _w ireless@tq s.co m f ax: (503) 615-8902 f o r technical questions and additional information on specific applications: email: in fo _w ireless@tq s.co m t he information provided herein is believed to be reliable; t r iquint assumes no liability for inaccuracies or omissions. t r iquint assumes no responsibility for the use of this information, and all such information shall be entirely at the user' s ow n risk. prices and specifications are subject to c hange w i thout notice. no patent rights or licenses to any of the circuits described herei n are implied or granted to any third party . t r iquint does not authorize or w a rrant any t r iquint product for use in lif e-support devices and/or sy stems. copy right ? 2005 t r iquint semiconduc tor, inc. all rights reserved .
|
